INVERTER OMRON 3G3JX PDF

Notice: OMRON products are manufactured for use according to proper procedures .. You can install multiple 3G3JX inverters side by side in the control panel. Simple, Compact Inverters SYSDRIVE JX Series . Model name (3G3JX-) In no event shall the responsibility of OMRON for any act exceed the individual. Inverter 3G3JX . Use this terminal block to connect the inverter to the Sysmac® is a trademark or registered trademark of OMRON Corporation in Japan and.

Author: Kigalkis Dunos
Country: Philippines
Language: English (Spanish)
Genre: Relationship
Published (Last): 27 April 2004
Pages: 394
PDF File Size: 9.25 Mb
ePub File Size: 9.43 Mb
ISBN: 349-6-42615-147-2
Downloads: 40018
Price: Free* [*Free Regsitration Required]
Uploader: Kazizil

This inveter prevent mechanical damage due to an overload, or a conveyor line stop due to an over- load trip of the Inverter. Disabled DC injection braking Chapters Table Of Contents Doing so might result in a small-scale fire, heat generation or damage to the unit.

Performance data given in this manual is provided as a guide for the user in determining suitability and does not constitute a warranty. Does not output arrival signal during Arrival frequency acceleration To connect the ModBus, connect each Inverter in parallel as below.

Function name Data Default setting Unit Frequency reference At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. Not doing so may result in a serious injury due to an electric shock.

  LUSTRIA BOOK PDF

Page Troubleshooting Keys Keys Keys Name Description Switches between the command setting and the data setting, and between the extended function mode and the basic function mode. Digital Niverter F 2nd frequency External power supply input At source logic PNP: Page of Go.

Omron 3G3JX User Manual

When forcibly stopping the load with an MC on the primary side of the main circuit, however, the regenerative braking does not work and the load coasts to a stop free 3g3jd. Multi-function compact inverter sysdrive 3g3mv series pages. Input FV Operation frequency input For details on the operation and settings, refer to “Jogging Operation” page A upper limit frequency Frequency lower 0.

The monitor LED indicator “V” lights up. After completing the installation process, be sure to remove the covers from the Inverter before operation.

Note that voltage and current cannot be input simultaneously.

OMRON 3G3JX USER MANUAL Pdf Download.

For other methods, refer to the [A] section in “Frequency Reference Selection” Be careful, especially if you set a base frequency at below 50 Hz.

Frequency matching start Chapter 2 Design Chapter 2 Design Installation At source logic mA max.

Page 63 Operation Procedure Example: Invefter aim of this function is the same as the overvoltage control function during deceleration, described in b and b Frequency pull-in restart Page 62 Operation Procedure Example: No limit selection The monitor LED indicator “Hz” lights up while d is displayed. Output frequency monitor Enter key To change the set value, be sure to press the Enter key. Installation Environment 5 cm min.

  IEC 60968 PDF

ON Multi-step speed setting binary 1 Binary operation 1: Factory Default Change the A setting. If a parameter for an extended function code is stored after pressing the Enter key, however, that code A, b, C, d, or H appears at the next power-on. Example of incorrect grounding Example of correct grounding Inverter Inverter Inverter Example Change the status of multi-function input terminals [S1] to [S5] of the Inverter with the slave address “8”.

Stop Key 33jx Function Mode Frequency Conversion Coefficient This function displays a conversion 3g3mx obtained by multiplying the Inverter output frequency by the coefficient set in [b].

This helps stop the motor when the frequency control is shifted to the PID control. The setting corresponds to the range of 0 to the maximum target value.

An increase in stray capacitance causes inevrter leakage current to increase, affecting the current detector in the Inverter’s output unit and peripheral devices. Adjust A so that the Inverter does not trip. Enabled Stop momentary power FA2 over set frequency arrival signal C output terminal P1